.. _Configuring Network:

Configuring Network
-------------------

|product_name| requires one network interface per server for management. On the **Component Installation** screen, you will need to specify a network interface to which to assign the network with the **Internal management** traffic type. After installation, you will not be able to remove this traffic type from the preconfigured network in the admin panel.

On the **NETWORK & HOST NAME** screen, you need to have at least one network card configured. Usually network is configured automatically (via DHCP). If manual configuration is required, select a network card, click **Configure...**, and specify the necessary parameters.

It is recommended, however, to create two bonded connections as described in :ref:`Planning Network` and create three VLAN interfaces on one of the bonds. One of the VLAN interfaces must be created in the installer and assigned to the admin panel network so that you can access the admin panel after the installation. The remaining VLAN interfaces can be more conveniently created and assigned to networks in the admin panel as described in the *Administrator's Guide*.

In addition, you can provide a unique hostname, either a fully qualified domain name (``<hostname>.<domainname>``) or a short name (``<hostname>``), in the **Host name** field. If do not, a unique hostname will be generated automatically by the installation program.

.. _Creating Bonded Connections:

Creating Bonded Connections
~~~~~~~~~~~~~~~~~~~~~~~~~~~

Bonded connections offer increased throughput beyond the capabilities of a single network card as well as improved redundancy.

You can create network bonds on the **NETWORK & HOSTNAME** screen as described below.

#. To add a new bonded connection, click the plus button in the bottom, select **Bond** from the drop-down list, and click **Add**.

   .. image:: /images/stor_install1.png
      :align: center
      :class: align-center

#. In the **Editing Bond connection...** window, set the following parameters for an Ethernet bonding interface:

   #. **Mode** to ``XOR``.
   #. **Link Monitoring** to ``MII (recommended)``.
   #. **Monitoring frequency**, **Link up delay**, and **Link down delay** to 300.

   .. image:: /images/stor_install2.png
      :align: center
      :class: align-center

   .. note:: It is also recommended to `manually set <http://docs.virtuozzo.com/virtuozzo_storage_administrators_command_line_guide/maximizing-cluster-performance/setting-up-network-bonding.html>`__ ``xmit_hash_policy`` to ``layer3+4`` after the installation. 

#. In the **Bonded connections** section on the **Bond** tab, click **Add**.

#. In the **Choose a Connection Type** window, select **Ethernet** from the in the drop-down list, and click **Create**.

   .. image:: /images/stor_install3.png
      :align: center
      :class: align-center

#. In the **Editing bond slave...** window, select a network interface to bond from the **Device** drop-down list.

   .. image:: /images/stor_install4.png
      :align: center
      :class: align-center

#. Configure MTU if required and click **Save**.

#. Repeat steps 3 to 7 for each network interface you need to add to the bonded connection.

#. Configure IPv4/IPv6 settings if required and click **Save**.

The connection will appear in the list on the **NETWORK & HOSTNAME** screen.

.. image:: /images/stor_install5.png
   :align: center
   :class: align-center

.. _Creating VLAN Adapters:

Creating VLAN Adapters
~~~~~~~~~~~~~~~~~~~~~~

While installing |product_name|, you can also create virtual local area network (VLAN) adapters on the basis of physical adapters or bonded connections on the **NETWORK & HOSTNAME** screen as described below.

#. To add a new VLAN adapter, click the plus button in the bottom, select **VLAN** from the drop-down list, and click **Add**.

   .. image:: /images/stor_install6.png
      :align: center
      :class: align-center

#. In the **Editing VLAN connection...** window:

   #. Select a physical adapter or bonded connection the VLAN adapter will be based on from the **Parent interface** drop-down list.

   #. Specify a VLAN adapter identifier in the **VLAN ID** field. The value must be in the 1-4094 range.

   .. image:: /images/stor_install7.png
      :align: center
      :class: align-center

#. Configure IPv4/IPv6 settings if required and click **Save**.

The VLAN adapter will appear in the list on the **NETWORK & HOSTNAME** screen.

.. image:: /images/stor_install8.png
   :align: center
   :class: align-center